SparkFun Thing Plus - ESP32-S3

Board
by SparkFunsparkfun-thing-plus-esp32-s3

Also known as: SparkFun ESP32-S3 Thing Plus, SPARKFUN_ESP32S3_THING_PLUS, sparkfun_esp32s3_thing_plus

Specifications

Radiosinherited from ESP32-S3

Wi-Fi
Wi-Fi 4 · 2.4 GHz
Bluetooth LE
BLE 5
Bluetooth Classic
no
802.15.4
no

USB

Native USB
yes
Connector
usb-c
Bridge chip
none — SoC native USB

Board

Form factor
thing-plus
Dimensions
58.42 × 22.86 mm
Battery connector
yes
Charging
yes

Display & extras

Extras
qwiicsd-cardrgb-led
Built onSparkFun Thing Plus - ESP32-S3 BoardESP32-S3 SoC

Feather-footprint ESP32-S3 board built on the ESP32-S3-MINI-1-N4R2 module (4 MB flash, 2 MB PSRAM), with USB-C wired straight to the chip's native USB, a 2-pin JST LiPo connector with MCP73831 charging and a MAX17048 fuel gauge, a Qwiic connector, a microSD slot on the SDIO bus, and a WS2812 RGB LED.

Firmware for this board

No firmware recipes yet — help add one.

Notes

  • SparkFun SKU WRL-24408: the product page reads "SKU: WRL-24408"
  • ESP32-S3-MINI-1-N4R2 module (4 MB flash, 2 MB PSRAM): the hookup guide reads "This Thing Plus uses the ESP32-S3-MINI1-N4R2 which features 4MB Quad SPI Flash memory and 2MB of PSRAM (Pseudo-static RAM)." The schematic labels the module ESP32-S3-MINI-1-N4R2. soc is referenced directly because the catalog has no esp32-s3-mini-1 module record
  • usb.bridge=native DERIVED: the hookup guide says the USB-C connector "connects directly to the ESP32-S3's USB serial converter" and that the ESP32-S3 "does not need any external UART-to-USB conversion"; the schematic routes the USB-C D+/D- lines as ESP20/D+ and ESP19/D- to the module with no bridge IC. usb_serial derived from usb.bridge (native) + soc usb.type serial-jtag
  • Battery: a 2-pin JST LiPo connector; the hookup guide reads "It also has an MCP73831 battery charger to charge an attached battery and a MAX17048 fuel gauge to monitor battery voltage levels."
  • Qwiic connector on "IO8/SDA and IO9/SCL"; microSD slot that "connects to the ESP32-S3's SDIO-4 pins"; addressable LED: "The WS2812 RGB LED connects the LED's Data In signal to IO46."
  • Peripheral power: a second RT9080 3.3V regulator feeds the 3.3V_P rail (Qwiic, fuel gauge pull-ups); "The RT9080's EN (Enable) pin is tied to ESP45 so users can drive it LOW in their code to disable this line."
  • Buttons: RESET and BOOT; "The BOOT button puts the ESP32-S3 into bootloader mode when held down during power on or reset."
  • dimensions_mm QUOTED: the hookup guide gives the board as "(58.42mm x 22.86mm)", matching SparkFun's official dimension drawing (2.3000 in x 0.9000 in). The product page's 2.55 in length disagrees with both and is not used
  • io.gpio_exposed=21 QUOTED: the hookup guide's PTH headers "break out a selection of 21 GPIO pins from the ESP32-S3"
  • io.gpio_pins: the schematic's ThingPlus header symbol and the dimension drawing's silkscreen enumerate the same 21 GPIOs: 43, 44, 8, 9, 13, 11, 12, 10, 14, 15, 16, 17, 18 (TX, RX, SDA, SCL, POCI, PICO, SCK, A0-A5) and 21, 7, 6, 5, 4, 2, 1, 42
  • io.gpio_free=21 DERIVED: of esp32-s3's soc.reserved_pins, strapping 0/3/45/46 and usb_flash_tied 19/20/35/36/37 are not on the headers (0 drives the STAT LED, 45 the RT9080 enable, 46 the WS2812, 19/20 the USB-C port, all onboard), so no subtraction applies: 21 - 0 = 21

Verify my board

Reads the connected chip over USB and checks it against what esp-atlas cites for SparkFun Thing Plus - ESP32-S3 — over Web Serial, no backend, nothing leaves your browser.

In-browser verify needs Web Serial: Chrome or Edge on a desktop. Safari, Firefox and phones cannot do it.

Serial monitor

Not connected.