T-Beam Supreme

Board
by LILYGOlilygo-t-beam-supreme

Also known as: T-Beam S3 Supreme

Specifications

Radiosinherited from ESP32-S3

Wi-Fi
Wi-Fi 4 · 2.4 GHz
Bluetooth LE
BLE 5
Bluetooth Classic
no
802.15.4
no

USB

Native USB
yes
Connector
usb-c
Bridge chip
none — SoC native USB

Board

Form factor
t-beam
Battery connector
yes
Charging
yes

Display & extras

Display
OLED SH1106
Extras
loragpsimumagnetometerrtcsd-cardqwiic
Built onT-Beam Supreme BoardESP32-S3 SoC

ESP32-S3FN8 LoRa + GNSS board (8 MB flash, 8 MB PSRAM) with an SX1262 or LR1121 radio, an L76K or u-blox M10 GNSS, an SH1106 OLED, QMI8658 IMU, magnetometer, PCF8563 RTC, BME280 sensor, microSD, and an AXP2101 PMU that charges an 18650 cell over USB-C.

Firmware for this board

No firmware recipes yet — help add one.

Notes

  • ESP32-S3FN8 with 8 MB flash and 8 MB PSRAM: the product page lists "ESP32-S3FN8 Dual-core LX7 microprocessor" with Flash 8MB and PSRAM 8MB, and LILYGO's hardware doc lists both T-Beam S3 Supreme builds as "ESP32-S3FN8 | 8MB(Quad-SPI) | 8MB(Quad-SPI)". The FN8 part has no in-package PSRAM; the core-board schematic carries the separate PSRAM/flash footprint
  • Wireless: the product page reads "2.4 GHz Wi-Fi & Bluetooth5 (LE)"
  • LoRa radio is SKU-dependent: the hardware doc gives "RF Module | SX1262" at "Frequency range | 868/915MHz" and "RF Module | LR1121" (sub-GHz and 2.4 GHz), and notes "Radio has its own SPI bus, and other peripheral SPI devices share the SPI bus." LILYGO's separate 144-148 MHz hardware page uses an SX1278 ("Frequency range | 144-148MHz"). The product page sells it as one listing with L76K or UBLOX GNSS at 433, 868, 915 or 920 MHz, plus "L76K 144~148 MHz"
  • GNSS is SKU-dependent: the hardware doc names the builds "T-Beam S3 Supreme L76K" and "T-Beam S3 Supreme Ublox" (u-blox MAX-M10) and notes "GNSS Wake-up is only available in L76K version"; "T-Beam Supreme GPS backup power comes from 18650 battery"
  • Sensors: six-axis IMU QMI8658 (product page "Six-axis IMU QMI8658"), PCF8563 RTC, BME280 temperature/humidity sensor, and a magnetometer that varies by build: "T-BeamSupreme has three magnetometer versions: QMC6310N, QMC6310U, and QMC6309, each with a different device address."
  • Power: AXP2101 PMU; the hardware doc gives "USB-C Input Voltage | 3.9V-6V" and "Charge Current | 0-1024mA" for the 3.7V 18650 cell held on the board
  • usb.bridge=native DERIVED: neither LILYGO schematic (T-Beam-S3-Core, T-Beam-S3-Supreme-V3.1) carries a USB-UART bridge chip; the USB-C data lines run as USB_DP/USB_DM to the ESP32-S3, and the hardware doc's Arduino settings use "USB CDC On Boot | Enable" with USB Mode "CDC and JTAG". usb_serial derived from usb.bridge (native) + soc usb.type serial-jtag
  • Expansion: UART1 TX/RX on GPIO43/44 at the "External QWIIC Socket" are the only pins the hardware doc's pin map marks free; it also lists an External M.2 Socket and an external pin header on the PMU rails. io is omitted: the doc does not enumerate the header GPIOs
  • Buttons: the product page lists "Boot (IO00) + Reset + Power Button"; the PWR button is wired to the PMU
  • Two hardware revisions: per the hardware doc, V3.1 replaces the magnetometer with a QMC6309, adds an onboard BMS and BME280/OLED address-selection resistors over V3.0

Verify my board

Reads the connected chip over USB and checks it against what esp-atlas cites for T-Beam Supreme — over Web Serial, no backend, nothing leaves your browser.

In-browser verify needs Web Serial: Chrome or Edge on a desktop. Safari, Firefox and phones cannot do it.

Serial monitor

Not connected.