ESP32-P4-Function-EV-Board
BoardAlso known as: esp32-p4-evboard
Specifications
Radiosinherited from ESP32-P4
- Wi-Fi
- none
- Bluetooth LE
- none
- 802.15.4
- no
USB
- Native USB
- yes
- Connector
- usb-c
- Bridge chip
- none — SoC native USB
Board
- Form factor
- devkit
Display & extras
- Extras
- ethernetrj45sd-cardmicspeaker-outaudio-codec-es8311
Espressif's (now end-of-life) ESP32-P4 multimedia devkit: an ESP32-C6-MINI-1 module provides Wi-Fi 6/BLE, with 16 MB SPI flash, MIPI CSI/DSI connectors, 10/100 Ethernet, MicroSD, an ES8311 audio path and native USB Serial/JTAG flashing. Not to be confused with its successor, the ESP32-P4X-Function-EV-Board.
Firmware for this board
No firmware recipes yet — help add one.
Notes
- Board version documented: v1.5.2. Espressif now lists this board under EOL (End of Life) Boards; the user guide points ESP32-P4X-Function-EV-Board (chip revision v3.x) users to that board's own guide -- a separate product, not this record
- Wireless comes from an onboard ESP32-C6-MINI-1 module (2.4 GHz Wi-Fi 6 & Bluetooth 5 LE), with its own programming connector for ESP-Prog or other UART tools
- Three USB Type-C ports plus one USB Type-A: USB Serial/JTAG port (recommended for flashing and debugging), USB Full-speed port, and a USB 2.0 Type-C port wired to the P4's USB 2.0 OTG High-Speed interface (device role); the USB 2.0 Type-A port shares that High-Speed interface in host role (up to 500 mA via a TPS2051C switch) and the two cannot be used simultaneously
- Onboard: RJ45 10/100 Mbps Ethernet via an Ethernet PHY on the P4 EMAC RMII interface, MicroSD slot (4-bit mode), microphone, ES8311 audio codec, NS4150B 3 W class-D amplifier driving a speaker output port (4 ohm, 3 W, 2.00 mm pitch), MIPI CSI and MIPI DSI 15-pin 1.0 mm FPC connectors, power switch, BOOT and Reset buttons
- Optional accessories (not on the board itself): 7-inch 1024 x 600 capacitive touch LCD with adapter board, and a 2MP MIPI CSI camera with adapter board
- PSRAM size is not stated for this board in its user guide or schematic, so psram_mb is omitted rather than guessed
- J1 header pins NC(0), NC(1) and NC(45) are excluded from gpio_pins: GPIO0/GPIO1 need the 32.768 kHz XTAL function disabled (move R61/R59 to R199/R197) and GPIO45 needs SD_PWRn disabled (move R231 to R100)
- The LCD adapter board uses J1 GPIO27 (RST_LCD) and GPIO26 (PWM) by default
- Hardware v1.4 (older revision of the same board) used a CP2102N USB-to-UART port with automatic download instead of the native USB Serial/JTAG port, had no Full-speed USB OTG Type-C port, and also broke out IO24/IO25 on the header
Verify my board
Reads the connected chip over USB and checks it against what esp-atlas cites for ESP32-P4-Function-EV-Board — over Web Serial, no backend, nothing leaves your browser.
In-browser verify needs Web Serial: Chrome or Edge on a desktop. Safari, Firefox and phones cannot do it.
Serial monitor
Not connected.
